A custom paper gift packaging box in 11 x 11 x 4.5 cm, built as a two-piece telescope with a half-depth lid. The lid is a cover with no bottom panel and sits over the outside of the tray, stopping a little over halfway down, so a strip of the base stays visible when the box is shut. Matte black outside, brown satin inside, no rim and no hardware.

Three Levels on the Side
| Feature | What it is | Note |
|---|---|---|
| Footprint | 11 x 11 cm | square in plan, straight walls |
| Height | 4.5 cm as shown | height is customised per order, the structure does not change |
| Lid skirt | a little over half the height | the cover reaches past the middle and stops |
| Base showing | the rest of the wall | visible below the step, all the way round |
| Corner | V-grooved and folded | sharp 90 degrees, no tape, no radius |
| Interior | brown satin, one continuous piece | draped over floor and walls, not a moulded tray |
The Skirt Stops Above the Base
Most two-piece boxes run the lid to the table, and the side reads as a single block. This one stops early on purpose. The cover’s lower edge lands above the base’s bottom edge, so the closed box shows three levels: the lid’s top face, the lid skirt, and the strip of base left showing, with one step between skirt and base and a fine shadow under the overhang.
That step is the whole difference between this box and a full-depth version. It is not a decoration and it is not a printing effect: it is a lid that was cut shorter, over a tray that was not. Nothing is glued on to make it, and there is nothing to peel off.

Satin, Draped Not Slotted
The tray is lined with one continuous piece of brown satin, laid over the floor and up the four inner walls and folded into the corners. There is no foam block, no moulded cavity and no divider. The fabric is there to hold the piece softly and to throw light back up at it, not to clamp it in place.
That matters for porcelain. A rigid insert has to be cut to one shape and grips only where it touches; a draped lining meets the piece along its whole underside and lets a cup or a dish settle into it. The folds take the shape of whatever is put in.

Matte Black With a Vertical Grain
The wrap is a matte black art paper with a fine vertical grain, so the surface reads as a soft dark field rather than a flat black panel. There is no gloss, no foil and no print on the sample: the box carries no mark at all.
The interior of the lid is black, the same colour as the outside. Only the tray carries the second colour, and only inside it, so the box stays restrained until it is opened.
What Fits: Porcelain and High Value Pieces
A cup, a saucer, a small dish, a bud vase, an ornament, a perfume bottle, a jewellery case, a presentation piece. Anything that needs to be shown rather than protected in transit for weeks.
The box is the retail layer, not the shipping pack: it goes inside a second, heavier outer case with padding, and that outer case takes the handling.

Height Is the Part You Change
The 11 x 11 cm footprint and the half-depth lid are the constant. Height is what gets specified: a short cup fits the sample height, a taller cup or a bottle needs the wall and the skirt raised together, and the proportions stay the same because both grow.
That is worth saying plainly, because a taller box with the same skirt would turn into a full-depth lid by accident. When you send a height, the skirt is set with it.
Insert Options Besides Satin
Satin is what the sample uses, and it can be replaced or supplemented: moulded EVA, sponge, EPE or a folded paper tray with compartments, all cut to your drawing. A common combination is satin on the floor with a card platform above it, so the piece sits high in the tray and the folds still show at the edges.
The satin colour is a choice as well. Brown is what the photographs show; any stock shade or a Pantone match is possible.
Paper, Board and Documents
The wrap and the grey board can be specified as recycled content, and paper can be bought from FSC certified mills on request. The certificate belongs to the mill; this factory does not hold one, and we do not describe the box as certified.
On file: ISO 9001:2015 certificate ZYC24Q00141R1S, valid to 2027-11-28, scope covering the production of paper packaging boxes excluding food inner packaging, and paper bags; EU RoHS reports; German LUCID registration DE2463045771631; French CITEO registration FR292146_01UOMY. We have run our own rigid box factory in Guangzhou since 2004. Ask for a free sample before you commit to a run.
Questions About a Half Lid Box
Is the lid supposed to stop above the base?
Yes. The skirt ends above the base’s bottom edge on purpose, which is what leaves the strip of base visible. A lid that reaches the table is a different construction.
Why does the lining look creased?
Because it is draped fabric, not a moulded insert. The folds are the material settling around the piece, and they differ slightly from box to box.
Can the height change without changing the look?
Yes, as long as the skirt grows with the wall. Send the height you need and the skirt proportion is set to match, so the step stays where it is.
Is there a rim or a band inside?
No. The mouth is one board thickness and the cavity wall is the tray’s own wall. Read the rest on the FAQ page.
For why the skirt stops where it does, see the half lid explained. Other lid-and-base builds are listed under lid and base boxes.













Reviews
There are no reviews yet.