A double open drawer watch box in three pieces: an outer sleeve open at both ends, an inner tray with a flocked watch insert, and a printed top board that travels with the tray. The tray slides out along the long axis from either side, so nothing has to be lifted or unfolded. Stock size is 17 x 6 x 3 cm; every other size is built to order.
| Structure | Three pieces: sleeve, tray, top board |
|---|---|
| Opening | Tray slides out from either end of the sleeve |
| Closed face | One continuous long side, no lid seam; flush end |
| Material | Black matte soft-touch paper over grey board |
| Insert | Black flocked watch cushion with strap channel |
| Stock size | 17 x 6 x 3 cm |
| Minimum order | 300 pcs per design |
What This Box Is
It is a presentation box for watches, built as a drawer rather than a lid. The outer sleeve is a tube with both ends open; the tray carrying the watch slides out from either end and is pushed back the same way. That single decision changes how the box is opened in a shop, how it is photographed, and how the insert has to be tooled.
Three Pieces: Sleeve, Tray, Top Board
The sleeve is four walls plus top and bottom panels, open at both ends. It is one continuous tube, so the long side reads as a single panel with no lid line anywhere along it.
The tray is a bottom panel with four walls, holding a black flocked insert with a channel for the strap. The top board is a flat printed board with a white pull tab at one end; it sits over the tray and moves out with it, so the buyer sees print first and product second.
Both Ends Open, One Tray
Because the sleeve has no closed end, there is no fixed front and back. A tray that was packed one way can be pushed out from the other side, which matters when the same box is used for retail facing in two directions, or when a buyer opens it from the side they are holding.
The two ends are interchangeable, not symmetrical by accident. The clearance between sleeve and tray is set so the slide is smooth and the end face stays flush when the tray is fully home.
Closed, One Continuous Side
Look at a closed box on the shelf: the long side is one surface from end to end, with a line only where the box meets the table. There is no second horizontal line partway down, no step, and no lid sitting on a body.
That is the difference between a drawer box and a lid box in one glance. A lid box announces itself by its lid line; a drawer box shows a clean block, and the opening only appears when the tray starts to move. Why the tray slides out both ends goes through the structure piece by piece.
Why The Insert Has A Strap Channel
A watch on a flat pad can rotate; a watch in a channel cannot. The channel runs across the insert, so the case sits in the cut-out and the strap passes underneath rather than wrapping over the top. The buckle is tucked out of sight and the dial stays square to the viewer.
Channel width is cut to the case, not to the strap: too wide and the case rocks, too narrow and the strap will not seat. That is why the insert is tooled from your drawing rather than picked from a stock list.
Black Soft-Touch Paper Over Grey Board
The surface is black matte soft-touch paper laminated to rigid grey board. The finish is fine-grained and non-reflective, which keeps fingerprints and ceiling glare away from the product — a real advantage with watches, where a glossy black lid turns into a mirror under shop lighting.
The board is wrapped on five faces, and the paper edge is visible at the cut edges, with the grey board layer readable underneath. That exposed edge is a construction fact, not a defect.
17 x 6 x 3 cm, And Any Other Size
The stock reference is 17 x 6 x 3 cm, lying flat: long enough for a watch on its cushion with room at the ends, deep enough for the case and the board. The proportion is deliberately long and low, which is what makes the drawer read as a drawer.
Any other size is built to order from your product outline. A new size means a new die and a new insert cavity, so it is quoted as its own project rather than as a variant of the stock box.
Printing On Soft-Touch Black
Hot foil in silver, gold or a matched colour; blind emboss and deboss; and screen printing. Soft-touch black takes foil and blind emboss cleanly, because the matte surface holds a crisp edge instead of bleeding under a film.
Where a light colour is required, screen printing or a foil is more reliable than offset on this surface. Send artwork as AI, PDF or CDR with outlined fonts and a defined colour reference.
What Goes Inside
Watches first: sports watches with a thick case, mechanical watches where the dial has to face the light, smart watches with a charging puck in the tray beside the cushion. The same construction, re-tooled, carries necklaces and chain items, pens, bracelets and other long-profile products.
Nothing about the outside changes when the contents change. What changes is the insert cavity and the tray depth. Watch paper box and blue double drawer watch box show the same family in other finishes.
Inserts Tooled To The Watch
Without a request the tray ships with a plain flocked cushion. When the watch is specified, the cavity is cut to the case width and the strap channel to the band, and the insert is approved on the sample before bulk.
Flocked paper is the default because it grips without scratching and reads as jewellery-grade. EVA is available where a harder hold is needed, and a long-profile channel replaces the cushion for necklaces.
Minimum Order And Quantity Tiers
Minimum order is 300 pcs per design. Quantity tiers for the stock 17 x 6 x 3 cm box are quoted per piece, FOB, and confirmed against the artwork and insert at order:
| 300 pcs | US$1.90 / pc |
|---|---|
| 500 pcs | US$1.75 / pc |
| 1000 pcs | US$1.25 / pc |
| 2000 pcs | US$0.90 / pc |
New sizes, new insert cavities and new print setups are quoted separately, because each one needs its own die or its own tooling.
Artwork, Die Line And Sample
Send artwork as AI, PDF or CDR with outlined fonts and a defined colour reference. The die line comes back for confirmation before anything is cut, and a pre-production sample is made from your artwork before bulk production.
A new size, a new insert cavity or a change of board grade means a new die. That is the one part of the process that cannot be absorbed into a repeat run, so it is quoted up front.
Quality And In-House Production
Our quality management system is certified to ISO 9001:2015, registration ZYC24Q00141R1S. Inspection runs at three points: incoming board check, in-line print check while the sheet is on press, and finished-goods inspection before packing.
Guangzhou Junye Packaging Industry Co., Ltd. has been making paper packaging since 2004. Prepress, cutting, printing, laminating, die-cutting, gluing and assembly all run in our own plant, so a deviation is caught at the press rather than after the boxes are glued.
Packed For Export
Each box is sleeved in a transparent PP bag first, because soft-touch paper scuffs against the next box more easily than a coated surface. The bags then go into an export carton in multiple rows and layers, and filled cartons are palletised for container loading.
Packing arrangement follows the box size and the print, and is confirmed per order rather than fixed in advance.
Questions Buyers Ask
What is the minimum order quantity?
300 pieces per design.
Can the box be printed with our logo?
Yes. Hot foil, blind emboss, deboss and screen printing are available on soft-touch black. Send artwork in AI, PDF or CDR with outlined fonts.
How does the box open?
The sleeve is open at both ends. The inner tray slides out along the long axis from either side; there is no hinge and no magnet.
Can you make a different size?
Yes. 17 x 6 x 3 cm is the stock reference; any other size is built to order from your product outline.
Can the insert fit a necklace instead of a watch?
Yes. The flocked cavity is tooled to your product — a watch cushion with strap channel, or a long-profile channel for necklaces.
Do you provide a sample before bulk?
Yes. An artwork proof and a pre-production sample are made before bulk production.
How are the boxes packed for export?
Each box is sleeved in a transparent PP bag, then packed in an export carton in multiple rows and layers, then palletised.
Are you certified?
Our quality system is certified to ISO 9001:2015, registration ZYC24Q00141R1S. We have been making paper packaging since 2004.





















Reviews
There are no reviews yet.