A kraft paper box for phone packaging, built as two pieces: a base tray and a deep cover with no bottom panel. The cover skirt runs the full height of the tray, so a closed box shows one continuous side wall — no lid line, no step, no strip of tray underneath. Stock size is 16 x 8 x 6 cm; every other size is built to order.
| Structure | Two pieces: base tray + deep cover, no bottom panel in the cover |
|---|---|
| Closed face | One unbroken side panel, base fully enclosed |
| Material | Natural kraft board, unbleached, matte |
| Stock size | 16 x 8 x 6 cm |
| Opening | Cover lifts straight up and off; no hinge, no flap, no sleeve |
| Interior | Plain; insert cavities tooled to your device on request |
| Brand | JUNYE, printed to your artwork |
What This Box Is
It is a packaging format for small electronics, not a fixed device fit. The construction stays the same across projects; the size, the board grade, the print and the insert are set from your product drawing. That is why the same box that carries a phone can be re-tooled for a tablet, a pair of earphones or a microphone without changing the way the package opens.
Two Pieces: A Tray And A Deep Cover
The base tray is a bottom panel with four walls, open at the top. The cover is four walls plus a top panel, and nothing underneath — a deep cover, not a shallow cap. Put them together and the cover encloses the tray from the outside.
There is no hinge, no folding flap and no sleeve. The cover lifts straight up and off in one movement, which is what a retail unboxing wants: a single gesture, no tearing, nothing to fold back.
Closed, The Side Is One Panel
Set the closed box on a shelf and look at one face. You see one surface from the top edge to the bottom edge, with a single clean line where the cover ends and the base begins to sit on the table. No second horizontal line, no ledge, no band of a different tone.
That is the whole test. If the side shows a step or an exposed strip, the cover is stopping short of the base; if it shows one panel, the cover is running the full height. On this box the tray disappears completely when the cover is on.
Why The Cover Runs Past The Tray Edge
A cover that reaches the table edge does three things a shallow lid cannot. It protects the base corner, which is the part that scuffs first in transit. It keeps the opening edge out of sight, so the box reads as a solid block on the shelf. And it gives the hand something to grip: the cover overhangs the tray by a hair on each side, so the fingers find an edge without a pronounced cap.
The trade-off is tolerance. A full-height skirt has to clear the tray on all four sides at once, so the die and the wrapping have to be consistent batch to batch. We cut and wrap in house, which is how that consistency is held.
Full Lid, Half Lid, Shallow Lid
Three ways to close a lid-and-base box, three different silhouettes on the shelf:
- Shallow lid: the cap sits on the tray and covers only the top few centimetres, so a wide band of tray stays visible. See the kraft paper box range.
- Half lid: the skirt drops about two thirds of the way, leaving the lower tray exposed as a visible plinth.
- Full lid: this box. The skirt reaches the bottom edge and the tray is enclosed, so the closed silhouette is a single mass.
If the product needs a visible plinth or a two-tone body, a half lid does that better. If the box has to look like one object and take handling in transit, the full lid is the right call.
Natural Kraft, Unbleached And Matte
The board is natural kraft: unbleached, matte, with the fibre and the sheet texture still showing. There is no film and no varnish over it. Paper edge thickness is visible at the rim, and the same bare board lines the inside, so an opened box looks consistent rather than half-finished.
Kraft is not a budget substitute for a coated wrap. It is a different surface with its own behaviour: it takes darker inks well, it scuffs less visibly than a gloss film, and it photographs as a material rather than as a colour. Kraft paper box packaging covers the board grades we hold.
16 x 8 x 6 cm, And Any Other Size
The stock reference is 16 x 8 x 6 cm, standing on its narrow face so the box presents tall and slim on the shelf. That proportion suits a phone with a charger and a cable beside it.
Any other size is built to order from your product outline. A new size means a new die, so it is quoted as its own project rather than as a variant of the stock box. Send the drawing with the internal dimensions you need and we will work back to the outside.
Printing On Kraft
Offset CMYK, spot colour, hot foil stamping, embossing, debossing, UV spot and screen printing are all available. Kraft is a warm, mid-tone sheet, and ink behaves accordingly: dark inks sit close to the expected colour, while light inks shift warm and lose contrast.
Where a clean light colour matters, a white primer goes down first and the ink sits on that. It is a decision to make at proof stage, not at press. Your brand mark can also go on unprinted as a foil or an emboss, which keeps the kraft face and still reads as finished.
What Goes Inside
Phones are the primary use, in retail and in e-commerce packs. The same construction, re-tooled, carries tablets, earphones and charging cases, microphones and small audio devices, power banks, cables and small accessories.
Nothing about the outside changes when the contents change. What changes is the insert cavity and the internal height, which is why we ask for the device drawing before quoting a size. Two starting points: custom printed phone box and earphone packaging box.
Inserts, Tooled To The Device
Without a request the box ships with a plain interior. That is deliberate: an insert that is not tooled to the actual device either grips too hard or lets the product move, and both look worse than a plain tray with a wrapped product inside.
When you do want one, EVA, flocked paper or a moulded pulp cavity is cut to your drawing. The cavity depth and the finger notch are set from the device, and the insert is approved on the sample before bulk.
Artwork, Die Line And Sample
Send artwork as AI, PDF or CDR with fonts outlined and a defined colour reference. The die line comes back for confirmation before anything is cut, and a pre-production sample is made from your artwork before bulk production.
A new size, a new insert cavity or a change of board grade means a new die. That is the one part of the process that cannot be absorbed into a repeat run, so it is quoted separately and up front.
Quality System And Documents
Our quality management system is certified to ISO 9001:2015, registration ZYC24Q00141R1S. Inspection runs at three points: incoming board check, in-line print check while the sheet is on press, and finished-goods inspection before packing.
Prepress, cutting, printing, laminating, die-cutting, gluing and assembly all happen in our own plant. Nothing in the chain is subcontracted, which is why a print problem is caught at the press rather than after the boxes are glued.
Made In Guangzhou Since 2004
Guangzhou Junye Packaging Industry Co., Ltd. has been making paper packaging since 2004: rigid boxes, folding cartons, paper bags, hang tags and fabric pouches for brand owners and importers.
The plant runs the whole sequence under one roof, from prepress to final assembly. For a buyer that mostly means one point of contact and one place where a deviation gets fixed.
Packed For Export
Every box is sleeved in a transparent PP bag first, so the printed face cannot scuff against the next box. The bags then go into an export carton in multiple rows and layers; single-piece cartons are not used for bulk orders.
Filled cartons are palletised and wrapped for container loading. Packing arrangement follows the box size and the print, and is confirmed per order rather than fixed in advance.
Questions Buyers Ask
Can the box be printed with our logo?
Yes. Offset, spot colour, foil, emboss, deboss, UV spot and screen are all available. Send artwork in AI, PDF or CDR with outlined fonts.
Is the lid a separate piece?
Yes. Two pieces: a base tray and a deep cover with no bottom panel. The cover skirt runs the full height of the tray, so the closed box shows one continuous side wall.
Can you make a different size?
Yes. 16 x 8 x 6 cm is the stock reference; any other size is built to order from your product outline.
Can you add an insert for a phone or earphone?
Yes. EVA, flocked paper or moulded pulp cavities are tooled to your device drawing.
Do you provide a sample before bulk?
Yes. An artwork proof and a pre-production sample are made before bulk production.
How are the boxes packed for export?
Each box is sleeved in a transparent PP bag, then packed in an export carton in multiple rows and layers, then palletised.
Are you certified?
Our quality system is certified to ISO 9001:2015, registration ZYC24Q00141R1S. We have been making paper packaging since 2004.





















Reviews
There are no reviews yet.